Every boiler manufacturer sets up a specific system of error codes, which you can find in technical documentation or read in the table below. Along with error codes and names, the table contains causes of malfunctions and lists of steps, which you should take to eliminate it.
TriangleTube CHALLENGER CC 85 boiler error codes
| Display | Error Description | Possible Solution |
|---|---|---|
| 10, 11,12, 13,14 | – CH Supply Sensor fault S1 | •Check wiring for break |
| • Check for proper flow direction | ||
| • Replace S1 | ||
| • E10 open sensor •E11 Short sensor | ||
| 20, 21, 22, 23, 24 | – CH Return Sensor fault S2 | • Check wiring for break |
| • Check for proper flow direction | ||
| • Replace S2 | ||
| • E 20 open sensor •E21 short sensor | ||
| 0 | – Sensor fault after self check | • Replace S1 and/or S2 |
| 1.28 | -Temperature too high | •Air in installation |
| • Pump not running | ||
| • Insufficient flow in installation, shut off valves closed, pump setting too low | ||
| • Flow switch sticking or miss-installed | ||
| 2 | – S1 and S2 interchanged | • Check water flow |
| • Check wiring | ||
| • Replace S1 or S2 | ||
| 4 | – No flame signal | • Manual Gas shut off valve closed |
| • No or incorrect ignition gap | ||
| • Gas supply pressure too low of failling | ||
| • Gas valve or ignition unit not powered | ||
| 5 | – Poor flame signal | • Condensate drain blocked |
| • Check adjustment of gas valve | ||
| 6 | – Flame detection fault | • Replace ignition cable + spark plug cap |
| • Replace ignition unit at gas valve | ||
| • Replace boiler controller | ||
| 8 | – Incorrect fan speed | • Fan catching on casing |
| • Wiring between fan and casing | ||
| • Check wiring for poor wire contact | ||
| • Replace fan | ||
| 29.3 | – Gas valve relay faulty | • Replace boiler controller |
| LOP | – Low CH system pressure | • Raise CH pressure above 7 psi [ 0.5 bar] |
| 3, 18, 19 | – Flue sensor Fault | •E18open sensor •E19 Short sensor |
| • Check/ Replace sensor | ||
| • E19 Excessive Temperature | ||
| • Clean heat exchanger | ||
| 7.17 | – DHW sensor Fault | • E17 open sensor |
| • Check/ replace sensor | ||
| • E7 Excessive temperature | ||
| • Check gas orifice | ||
| • Check combustion settings | ||
| 50F | – Improper frequency | • Verify ground |
| • Frequency should be between 45 and 65 Hz |
TriangleTube Prestige Excellence boiler error codes
| Error | Description |
|---|---|
| E00 | Flame detected prior to burner startup |
| E02 | Failed ignition after 5 attempts |
| E03 | Gas valve harness not properly connected |
| E04 | Power supply lost after lockout occured |
| E05 | Internal control failure |
| E06 | |
| E07 | |
| E08 | |
| E09 | |
| E11 | |
| E12 | External limit (terminals 13 & 14) control is OPEN |
| E13 | Internal control failure |
| E14 | |
| E15 | |
| E16 | |
| E17 | |
| E18 | Supply Temperature exceeds 212°F |
| E19 | Return temperature exceeds 212°F |
| E25 | Supply temperature increased too rapidly |
| E28 | No blower signal present |
| E29 | Blower signal does not reset to zero |
| E31 | Supply temperature sensor is short circuited |
| E32 | Return temperature sensor is short circuited |
| E36 | Supply temperature sensor is OPEN |
| E37 | Return temperature sensor is OPEN |
| E44 | Internal control failure |
| E52 | Flue temperature exceeds 250°F |
| E60 | Internal control error – failure to read parameters |
| E61 | Internal control failure |
| E65 | Inadequate power supply to the fan |